Santa Fe Factory installed remote starter causing my new car to not start


Can a remote starter cause a car to not start?

Hood Pin Switches Or Sensors



The single biggest thing that can cause a remote starter not to engage is a faulty or missing hood switch. This device gets installed under the hood of your vehicle and prevents the engine from starting when the hood is up.

Why is my automatic start not working?

Reasons Your Remote Start is Not Working:



Vehicle Not in ‘Park’ Too Many Remote Start Attempts. Coolant and Oil Pressure. Unlatched Hood.

How do I disable aftermarket remote start?

How to Disable Remote Starters

  1. Make sure your automobile is turned off and that your key is out of the ignition.
  2. Remove the dashboard panels around the ignition to locate the toggle switch underneath the steering column. …
  3. Look for the module with four wires. …
  4. Flip the toggle switch on this module from “On” to “Off.”


How do you reset a remote car starter?

Insert your ignition key and turn it to Accessory (or press the start button once without pushing the brake pedal). Press the Lock button on your remote car starter. Within five seconds of turning it on, turn your key back to the “off” position (or press the start button again).

Can remote start damage alternator?

Can Car Remote Starter Cause Electrical Problems? It is possible, however, to unnecessarily charge your battery with a remote starter. Your battery and electrical system might experience issues if you were unable to install an aftermarket model in your vehicle.

Do remote starters drain battery?

Yes, this convenience has its drawbacks: it’s been shown that when you use a remote starter, your battery will drain more quickly than if you had started the engine manually by turning the key in the ignition. But for many people–especially those with busy schedules–the benefits outweigh any inconvenience.

Does remote start work with check engine light on?

If the ‘Check Engine Light’ or Malfunction Indicator Lamp (MIL) is illuminated, the remote start will not work.

Will a weak battery cause remote start not to work?

Cause: It is rare, but does happen – in most cases, this is caused by a dead battery in the vehicle or the battery having been disconnected when being serviced. Remote starters usually have some type of non-volatile memory to retain things like programming features and remote control codes.

What is valet mode on remote starter?

Valet mode is a setting in Firstech systems that will shut down the alarm system and the remote starter. It will only allow the remotes to retain key-less entry to be used to lock and unlock the doors.

How do you program a push to start key fob?

Programming a Push-Button Starter

  1. With the fob in your hand, get into the driver’s seat, closing the door behind you. …
  2. When you’re ready, press your car’s start button 15 times in quick succession, with no more than two seconds between each attempt. …
  3. After the 15th button press, push the lock button on your fob.


How do I program a new remote starter for my key fob?

antennamediatorino.eu
So what you gotta do is you got to press and hold your button on your key fob it'll beep once to let you know that that one's programmed. And then you do it to your other fob. And it'll beep. Again.

Why is my car remote not working?

Check and replace the key fob battery as needed. Take the key fob apart and check for broken contacts or misaligned buttons. Reprogram your remote yourself or have a professional do it. Replace your remote if necessary.

What can interfere with car remotes?

Armchair electricians on social media and elsewhere have raised a number of potential causes—automatic door sensors, shopping cart proximity locks, Wi-Fi, and even some security camera systems have all been reported to mess with smart fob operation elsewhere.

How do you test if a key fob is transmitting?

antennamediatorino.eu
Press the on button and let the light cycle for a minute. Once the red light is on being a key fob over to this window. Right here and press the button. You'll see in this case.

How do I reset my Hyundai key fob?

Stick the key to your Hyundai into the vehicle’s ignition cylinder. Turn the key to the “ACC” or “Accessory” ignition position. Hold down the “Open” or “Unlock” button on the keyless entry FOB until the vehicle’s lights flash. The keyless entry FOB is now reprogrammed to your Hyundai vehicle.

Can I program my own Hyundai key fob?

Tips. Keep in mind that the key fob programming instructions will only work if you have a key fob already programmed to a previous Hyundai that you owned. If you are purchasing a new Hyundai, you will need to visit a Hyundai service center to have an expert technician program the key fob to your vehicle instead.

How do you start a Hyundai without a key fob?

antennamediatorino.eu
Insert the key fob with the buttons up or towards the glovebox. And start as normal pushing the start/stop button while stepping on the brake. The car recognizes the fob.