P0016 MERCEDES-BENZ code

P0016 definition: The correlation of the camshaft and crankshaft positions on bank 1 is incorrect based on the intake camshaft position sensor. Repair Urgency: Fix this code immediately (same day if possible) to avoid internal engine damage.

How do I fix the code P0016 on my Mercedes?

What repairs can fix the P0016 code?

  1. Resetting the fault codes and performing a road test.
  2. Replacing the camshaft sensor on bank 1.
  3. Repairing the wiring or connection to the camshaft OCV or camshaft sensor.
  4. Replacing the camshaft OCV for bank 1 exhaust camshaft.
  5. Replacing the timing chain and guides.


How do you fix trouble code P0016?

How to fix a P0016 OBD-II code?

  1. Repair the wiring or connections to the components, including the camshaft sensor or camshaft OCV.
  2. Check the timing chain and guides and replace if needed.
  3. Replace the camshaft OCV for bank 1 exhaust camshaft.

What could cause a P0016 code?

When the PCM issues a code P0016, the car may be experiencing one of these issues: Stretched or damaged timing chain or timing belt. Damaged camshaft or crankshaft reluctor wheel. Bad crankshaft sensor.

  P0320 MERCEDES-BENZ code

How much does it cost to fix P0016?

But if the problem has something to do with a broken timing chain, timing belt, and/or tensioner, you can expect to spend around $200 for parts and labor depending on the make and model of your vehicle. The mechanic will also check the cam and crank patterns to rule out a broken sensor or tone ring.

Where is camshaft position sensor a bank 1 located?

Beneath the timing belt cover is where the CMP Sensor is mounted. The camshaft position sensor can be found in the right side of the engine compartment at the rear of the valve cover.

Where is the camshaft position correlation Bank 1 sensor A?

The “A” Indicates the Intake Camshaft, located to the intake side of the Cylinder Head. “Bank 1” denotes the Engine Bank that contains the Number One Cylinder.

Can I drive with code P0016?

Diagnosis: This trouble code can cause the vehicle to be hard to start and run rough. In some cases, the vehicle may not be driveable. It should be addressed as soon as possible.

Is it safe to drive with P0016 code?

Is It Safe To Drive With P0016 Code? A vehicle that contains this trouble code will have difficulty starting or running smoothly. It is possible for a vehicle to be left disabled. We should address it as soon as possible.

Can low oil cause a P0016 code?

Causes of Code P0016



While a worn timing belt is the most likely cause, you can’t rule out a faulty solenoid or even something as simple as low oil creating the problem.

  P0445 MERCEDES-BENZ code

How do you fix a camshaft to crankshaft position correlation fault?

The most common solution to this code is the replacement/repair of wiring, followed by replacement of crankshaft/camshaft position sensors if the engine timing is known to be good. Less common solutions include replacement of reluctor rings, or VVT/VCT oil control solenoids.

What is bank1 sensor B?

Note that the “B” means that this sensor is located in the exhaust side of the cylinder head. Bank 1 means that the sensor is located in the engine bank with cylinder 1.

What does Correlation Bank 1 mean?

Diagnostic trouble code (DTC) P0017 stands for “Camshaft Position B – Camshaft Position Correlation (Bank 1).” Like P0016, this code indicates that your car’s powertrain control module (PCM) detects a misalignment between the crankshaft and camshaft positions.

How much does it cost to fix P0017 code?

The cost of fixing error code P0017 varies, depending on the culprit. If a scan tool confirms the camshaft position sensor is the cause, the budget to spend around $25 to $80. The amount here is for the replacement sensor alone.

How do I fix code P0019?

What repairs can fix the P0019 code?

  1. Scan, clear, and retest the vehicle to verify whether the code comes back.
  2. Replace the camshaft sensor to the camshaft on bank 2.
  3. Repair any damaged wiring connections to the camshaft sensor or the OCV.
  4. Replace the Engine Control Module.