2002 Ford Escape sputters at and accelerates slowly from stops

The most common causes for slow acceleration in Ford Escape are clogged air filter, dirty mass air flow sensor (MAF), clogged fuel filter, fuel pump malfunction, faulty oxygen sensor, dirty throttle body, worn spark plugs and clogged catalytic converter.

Why is my Ford Escape sputtering?

Fuel injector nozzles can become clogged over time, which can lead to a sputtering engine, slow acceleration and the car not having enough power. Fuel injectors can be cleaned if the problem is caught early, but as the conditions worsens, the injectors may have to be replaced.

What causes Ford Escape to not accelerate?

Defective Fuel Pump: The fuel pump pulls the fuel from the gas tank to the engine via the fuel lines. If the pump stops working, malfunctions, or becomes clogged, it will not supply enough fuel to the injectors. This can cause the vehicle to accelerate slowly, or even sputter and stall, especially at high speeds.

What causes delayed acceleration?

An engine that is hesitating to accelerate is most likely dealing with a fuel/air mixture that is too lean. Engine’s that are running inefficiently will begin to show signs like hesitation which will only become worse over time.

Why does my car stop accelerating Sometimes when I press the gas?

If the exhaust system somehow becomes obstructed, excessive backpressure is created, and exhaust gases can get pushed back into the engine through the valves. The result is an engine that can’t breathe properly, causing a lack of acceleration.

How do I get my Ford Escape out of limp mode?

The next fix you can try is to shut off the engine and let it rest for at least 5 minutes. During this time you can check the engine oil level, as well as the level of all the other fluids under the hood. Sometimes, this brief rest will allow the computer to reset itself and bring it out of limp mode.

What year Ford Escapes are being recalled?

Ford Motor Company (Ford) is recalling certain 2018 F-150, 2018-2020 F-250, F-350, and 2019 Escape vehicles equipped with Continental tires. On the affected vehicles, it is possible that one or more tires were cured for too long during tire production.

Does Ford Escape have transmission problems?

Overall, Ford Escapes are slightly more prone to problems (most notably, transmission problems) than similar models of similar years. The Ford Escape has 4,167 reported issues on CarComplaints.com, with transmission issues accounting for many of those.

How do you check the transmission fluid on a Ford Escape?

Transmission Fluid Level Check Ford Escape (2013-2019) S 2.5L 4 Cyl.

  1. Remove Dipstick – Access point for transmission fluid.
  2. Add Fluid – Determine correct fluid type and add fluid.
  3. Replace Dipstick – Put the dipstick / cap back in place.
  4. More Info. – Additional information on checking trans. fluid levels.

Where is the fuel filter on a Ford Escape?

The fuel filter is always going to be found between the fuel tank and the engine. For most vehicles, the fuel filter is located inside the top of the fuel tank, right where it connects with the fuel line, although on some cars if might be elsewhere along the fuel line.

Why does my 2013 Ford Escape stall?

Just the Facts: Ford Motor Co. is recalling 159,395 2013-’14 Ford Focus ST hatchbacks and Ford Escape SUVs in North America because of a stalling risk linked to defective engine wiring harnesses. No accidents or injuries have been linked to the recall. The recall will begin the week of September 29.

What does engine fault mean on a Ford Escape?

What Is Engine Fault 2018 Ford Escape? You have to keep the engine light on in the 2018 Ford Escape to prevent the issue from occurring. A solution need not need to rush on from there. When these lights flash, it indicates that there is a bad engine misfire that is letting unburned fuel go into the exhaust.

Where is the purge valve located on a 2013 Ford Escape?

The evaporator canister purge valve is located beneath the air filter and intake hose on Your 2013 Ford Escape. It opens at specific times to let fuel vapors stored in the canister be drawn into the intake manifold and burned as part of the combustion process.

Where is the EGR valve located on a 2011 Ford Escape?

The EGR valve sits on the top of the engine near the rear of the block and looks like a round disk with a small vacuum tube attached to the top center of the disk.

How do you test a EGR valve?


Using. It's a little tough to see the the EGR valve it's underneath the airbox.

How do you clean an EGR valve?

How to Clean EGR Valve?

  1. Spray cleaner in both openings of the EGR valve. …
  2. If it’s really dirty, you may need to use a pick to scrape off the bigger chunks of carbon or a wire brush.
  3. You may also need to let the cleaner sit in the valve for several hours.
  4. Don’t be afraid to use too much cleaner.